35 ft 3/8 in. x 5/8 in. Mini Split Installation Kit
DABUND 35 ft 3/8 in. x 5/8 in. Mini Split Installation Kit combines a pre-insulated copper refrigerant line set with essential accessories for compatible ductless mini split, heat-pump and HVAC installations.
The kit includes a 3/8 in. liquid line and 5/8 in. suction line with factory-applied insulation, communication wire, condensate drain hose, wall pipe, protective wall cover and flare nuts.
The 35 ft line-set length is approximately 10.67 m. The refrigerant tubing is made from 99.9% pure copper, while the featured configuration uses White PE insulation designed for compatible indoor and outdoor HVAC installations.
Quick Answer: This 35 ft mini split installation kit includes a 3/8 x 5/8 pre-insulated copper line set plus communication cable, condensate drain hose, wall-entry accessories and flare nuts for compatible HVAC installations.
35 ft 3/8 x 5/8 Installation Kit Specifications
| Product Type | Mini Split Installation Kit |
| Line Set Size | 3/8 in. x 5/8 in. |
| Liquid Line | 3/8 in. |
| Suction Line | 5/8 in. |
| Length | 35 ft / approximately 10.67 m |
| Copper Material | 99.9% Pure Copper |
| Insulation | Factory-Applied White PE Insulation |
| Listed Insulation Temperature Range | -40°C to 120°C for applicable White PE construction |
| Included Accessories | Communication cable, drain hose, wall pipe, wall cover and flare nuts |
| Application | Compatible ductless mini split, heat-pump and HVAC installations |
Mini Split Installation Kit Video
What Is Included in the Complete Installation Kit?
| Component | Description |
|---|
| Refrigerant Line Set | 3/8 in. liquid line + 5/8 in. suction line, 35 ft |
| Factory Insulation | Pre-installed White PE insulation |
| Communication Cable | For compatible indoor and outdoor unit connection |
| Condensate Drain Hose | For condensate drainage |
| Wall Pipe | Protects the piping at wall penetration points |
| Wall Cover | Provides a finished wall-entry transition |
| Flare Nuts | For compatible refrigerant-line connections |
99.9% Pure Copper Refrigerant Line Set
The refrigerant line set uses 99.9% pure copper tubing for compatible air-conditioning and heat-pump installations.
The 3/8 in. liquid line and 5/8 in. suction line should always be checked against the refrigerant piping dimensions specified by the equipment manufacturer.
Factory-applied insulation reduces additional on-site insulation work and helps control heat transfer and condensation around the refrigerant tubing.
Copper Line Set and Insulation Video

99.9% Pure Copper

White PE Insulation

Flare Nut
White PE Insulation Structure
The featured insulation construction uses an embossed PE outer layer, an IXPE foam middle layer and a closed-cell inner structure.


Insulation Pipe Production

Insulation Pipe Warehouse

Inner Insulation Layer
Embossed PE Outer Layer
The embossed PE outer layer is designed to provide wear resistance and UV resistance for compatible HVAC installations.
IXPE Foam Middle Layer
The dense IXPE foam layer helps provide thermal insulation, impact absorption and resistance to moisture penetration.
Closed-Cell Inner Structure
The closed-cell inner structure helps reduce heat transfer and moisture penetration around the copper refrigerant tubing.
The listed temperature range for the applicable White PE construction is -40°C to 120°C.
Complete 35 ft HVAC Installation Package
Combining the refrigerant line set, communication cable, condensate drain hose and wall-entry components in one kit helps simplify purchasing and reduces the number of individual installation parts that need to be sourced separately.
The 35 ft length is useful where the indoor evaporator and outdoor condenser require a longer piping route than shorter standard installation kits.

Available Mini Split Installation Kit Sizes
| Line Set Size | Available Lengths | White PE Insulation | Listed Flame-Resistance Options |
|---|
| 1/4 + 3/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/4 + 1/2 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/4 + 5/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 5/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 3/4 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/2 + 3/4 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 7/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
General Line Set Size and Capacity Reference
The following capacity ranges are general references for the DABUND installation kit family. Final refrigerant-line sizing must follow the HVAC equipment manufacturer's specifications.
| Line Set Size | General Ton Reference | General BTU Reference |
|---|
| 1/4 + 3/8 in. | 0.75–1.0 Ton | 9,000 / 12,000 BTU |
| 1/4 + 1/2 in. | 1.5–2.0 Ton | 12,000 / 18,000 BTU |
| 1/4 + 5/8 in. | 2.0–2.5 Ton | 24,000 / 30,000 BTU |
| 3/8 + 5/8 in. | 3.0–4.0 Ton | 36,000 / 48,000 BTU |
| 3/8 + 3/4 in. | 4.5–6.0 Ton | 54,000 / 72,000 BTU |
| 3/8 + 7/8 in. | 6.0–8.0 Ton | 72,000–96,000 BTU |
These ranges are general references only. Always follow the equipment manufacturer's specified liquid-line size, suction-line size, maximum piping length and elevation requirements.
How to Select the Correct Mini Split Installation Kit
Confirm the Refrigerant Line Sizes
Verify that the HVAC equipment requires a 3/8 in. liquid line and 5/8 in. suction line before ordering this kit.
Confirm the Required Installation Length
Measure the full piping route between the indoor and outdoor units and confirm that the 35 ft line-set length is suitable.
Check Maximum Allowable Line Length
Confirm the equipment manufacturer's maximum piping length, allowable elevation difference and refrigerant charge requirements before installation.
Confirm Accessory Requirements
Check the required communication cable, drain hose, wall-entry components and flare connection requirements for the specific HVAC system.
Installation Considerations
Plan the full route for refrigerant tubing, communication wiring and condensate drainage before beginning installation to avoid unnecessary bends and routing conflicts.
Use the supplied wall pipe and protective cover where the lines pass through the wall to help prevent abrasion and provide a cleaner installation finish.
Refrigerant-line routing, condensate drainage, flaring, evacuation and commissioning should follow the HVAC equipment manufacturer's installation instructions.
DABUND Mini Split Installation Kit Factory
DABUND manufactures insulated copper pipe, mini split line sets, installation kits, aluminum pipe and related HVAC installation products.

Insulation Test Documentation
DABUND maintains test documentation for applicable insulation constructions, including references to ASTM E84, UL94, ASTM D1056 and ASTM G21.
Buyers requiring specific project certification should confirm the exact insulation material, thickness and applicable test report before ordering.

International HVAC Exhibitions
DABUND participates in international HVAC exhibitions where distributors and professional buyers can review mini split installation kits, line sets and related HVAC products.

Frequently Asked Questions
What is included in this 35 ft mini split installation kit?
The kit includes a 35 ft 3/8 in. x 5/8 in. pre-insulated copper line set, communication cable, condensate drain hose, wall pipe, wall cover and flare nuts.
What does 3/8 in. x 5/8 in. mean?
It refers to the listed outside diameters of the two refrigerant tubes: 3/8 in. for the liquid line and 5/8 in. for the suction line.
How long is this mini split line set?
The refrigerant line set is 35 ft long, approximately 10.67 m.
What copper material is used?
The refrigerant tubing is listed as 99.9% pure copper.
Is the copper tubing pre-insulated?
Yes. The refrigerant tubing is supplied with factory-applied insulation.
What insulation configuration is shown on this product?
The featured product configuration uses White PE insulation with a multilayer construction.
What insulation thicknesses are available?
Listed White PE insulation thicknesses include 8 mm, 9 mm, 10 mm, 13 mm, 19 mm and 25.4 mm.
What is the listed insulation temperature range?
The applicable White PE insulation construction is listed for temperatures from -40°C to 120°C.
What size air conditioner can use a 3/8 x 5/8 line set?
A 3/8 in. x 5/8 in. line set is listed as a general reference for some 3–4 ton or 36,000–48,000 BTU systems. Final refrigerant-line sizing must follow the equipment manufacturer's requirements.
Can this kit be used with every mini split system?
No. Compatibility depends on the required refrigerant-line sizes, connection type, maximum piping length and other equipment-specific requirements.
Is this kit listed for R410A and R32 applications?
The product information lists compatibility with common HVAC refrigerants including R410A and R32. Final suitability should be verified against the HVAC equipment manufacturer's specifications.
Does the kit include a drain hose?
Yes. A condensate drain hose is included in the listed accessory package.
Does the kit include communication cable?
Yes. Communication cable is included for compatible indoor and outdoor unit connections.
Are wall-entry accessories included?
Yes. The kit includes a wall pipe and protective wall cover.
Can DABUND provide free samples?
Yes. The listed policy provides up to three free samples for qualified requests, with the buyer paying the express freight. View Sample Information
What payment terms are available?
Available payment methods include T/T, L/C at sight and credit card.
What delivery terms are available?
Available delivery terms include EXW, FOB, CFR and CIF.
Does DABUND support OEM and ODM?
Yes. OEM and ODM services, including logo customization, are available for suitable orders.
What is the typical delivery time?
The listed typical delivery time is approximately 15–20 days, depending on order quantity and production requirements.