25 ft 1/4 in. x 1/2 in. Split AC Installation Kit
The DABUND 25 ft 1/4 in. x 1/2 in. Split AC Installation Kit provides the main refrigerant piping and installation components required for compatible ductless mini split air conditioners, heat pumps and split AC systems.
The kit combines a 25 ft pre-insulated copper line set with communication cable, an approximately 3 m condensate drain hose, wall sleeve, protective cover and pre-flared copper ends with nuts.
The refrigerant line set uses a 1/4 in. liquid line and 1/2 in. suction line made from 99.9% pure copper. The source product information references ASTM B280 and C12200 for the copper tubing.
Quick Answer: This 25 ft 1/4 x 1/2 HVAC installation kit combines insulated copper refrigerant tubing, communication wire, drain hose, wall-entry accessories and pre-flared connections for compatible 12,000–18,000 BTU / 1.5–2.0 ton mini split systems. Final line-set sizing must follow the HVAC equipment manufacturer's specifications.
Split AC Installation Kit Video
What Is Included in the 25 ft HVAC Installation Kit?
| Insulated Copper Line Set | 1/4 in. + 1/2 in., 25 ft / approximately 7.62 m |
| Liquid Line | 1/4 in. / 6.35 mm |
| Suction Line | 1/2 in. / 12.70 mm |
| Communication Cable | Included according to the source kit configuration |
| Drain Hose | Approximately 3 m |
| Wall Sleeve | Included |
| Protective Wall Cover | Included |
| Copper Connections | Pre-Flared Ends with Copper Nuts |
The exact communication-cable specification, drain-hose dimensions, wall-sleeve dimensions and accessory quantities should be confirmed for the ordered configuration.
Pre-Insulated 1/4 x 1/2 Copper Line Set
The kit uses a paired 1/4 in. liquid refrigerant line and 1/2 in. suction line with factory-applied insulation.
Factory insulation reduces the need for additional field wrapping and helps provide more consistent thermal and condensation protection along the copper tubing.
Buyers should verify that the selected air-conditioning or heat-pump model specifically requires these exact copper tube diameters before ordering.
Pre-Flared Copper Ends with Nuts
The source product information states that both ends of the copper tubing are pre-flared and supplied with nuts.
Pre-flared ends can reduce field preparation when the flare geometry and nut dimensions match the selected HVAC equipment.
Installers should inspect each flare before connection and tighten flare nuts according to the HVAC equipment manufacturer's specified torque requirements.
Copper Line Set Video
99.9% Pure Copper Refrigerant Tubing
The source product information specifies 99.9% pure copper for the refrigerant line set and references ASTM B280 and C12200 standards.
Copper provides thermal conductivity, corrosion resistance and installation flexibility for compatible mini split, split AC and heat-pump systems.

99.9% Pure Copper

White PE Insulated Pipe

Copper Nut
White PE and Black Rubber Insulation Options
The source page lists both White PE and Black Rubber insulation options. White PE is the primary insulation configuration shown in the product images and family table.
Factory-applied insulation helps limit heat transfer, reduce condensation around cold refrigerant tubing and protect the copper pipe during installation.
UV-Resistant Surface
UV-resistant insulation is referenced for compatible outdoor HVAC installations. Final outdoor suitability depends on the exact insulation configuration and exposure conditions.
Moisture and Condensation Protection
The insulation structure helps reduce moisture penetration and surface condensation during normal HVAC operation.
Listed Temperature Range
The source technical table lists an insulation temperature range of approximately -40°C to 120°C. Confirm this range for the exact insulation material and thickness ordered.
White PE Embossed Insulation

Triple-Layer White PE Insulation Structure
Outer Layer
The source describes a UV-resistant PE film outer layer for protection against environmental exposure.
Middle Layer
IXPE foam is referenced as the middle insulation layer for thermal protection and cushioning.
Inner Layer
A closed-cell inner structure is referenced to provide insulation around the copper refrigerant tubing.

Thermal Insulation Pipe Production

Insulated Pipe Warehouse

Inner Layer Insulated Pipe
Benefits of the 25 ft Installation Kit
Simplifies Component Sourcing
Combining refrigerant tubing, communication cable, drain hose and wall-entry accessories in one kit can reduce separate sourcing work for contractors and distributors.
Factory-Insulated Copper Tubing
Factory-applied insulation reduces additional field insulation work and helps provide more consistent coverage around the copper refrigerant tubing.
Fewer Intermediate Connections
A continuous 25 ft copper line reduces the need for unnecessary intermediate joints when the required installation route fits within this length.
Pre-Flared Connections
Pre-flared ends with nuts reduce field preparation when they match the selected equipment connections.
HVAC Applications for 1/4 x 1/2 Line Sets
The wider DABUND product family lists the 1/4 in. + 1/2 in. line-set configuration as a general reference for some medium-capacity mini split air-conditioning systems.
12,000 BTU mini split air conditioners
18,000 BTU mini split air conditioners
General 1.5 ton systems
General 2.0 ton systems
Residential HVAC installations
Light commercial air-conditioning systems
Compatible heat-pump installations
These capacity values are general references only. Final refrigerant-line sizing must follow the HVAC equipment manufacturer's exact specifications.
Technical Specifications
| Feature | Details |
|---|
| Product Name | 25 ft 1/4 in. x 1/2 in. Split System Air Conditioner Installation Kit |
| Length | 25 ft / approximately 7.62 m |
| Liquid Line | 1/4 in. / 6.35 mm |
| Suction Line | 1/2 in. / 12.70 mm |
| Copper Material | 99.9% Pure Copper |
| Insulation Options | White PE / Black Rubber |
| Listed Temperature Range | -40°C to 120°C; confirm applicability to the exact insulation configuration |
| Applicable Systems | Compatible Mini Split AC / Ductless Split AC / Heat Pump Systems |
| General Capacity Reference | 12,000–18,000 BTU / 1.5–2.0 Ton |
| Copper Standards | ASTM B280 / C12200 referenced in the source |
| Insulation Documentation | Applicable certification depends on the exact insulation material and ordered configuration |
Available Split AC Installation Kit Sizes
| Size | Available Lengths | White PE Insulation | Listed Flame-Resistance Options |
|---|
| 1/4 + 3/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/4 + 1/2 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/4 + 5/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 5/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 3/4 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/2 + 3/4 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 7/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
Length Note: This specific SKU is 25 ft / approximately 7.62 m. The wider family table lists 7 m and 10 m as adjacent metric configurations, so buyers should specify the exact finished 25 ft kit when ordering.
Line Set Size and Air Conditioner Capacity Reference
| Line Set Size | General Ton / HP Range | General BTU Range | Typical Application |
|---|
| 1/4 + 3/8 in. | 0.75–1.0 Ton / 0.75P–1P | 9,000–12,000 BTU | Small mini split air conditioner |
| 1/4 + 1/2 in. | 1.5–2.0 Ton / 1.5P–2P | 12,000–18,000 BTU | Medium mini split air conditioner |
| 1/4 + 5/8 in. | 2.0–2.5 Ton / 2P–2.5P | 24,000–30,000 BTU | Split AC and heat-pump system |
| 3/8 + 5/8 in. | 3.0–4.0 Ton / 3P–4P | 36,000–48,000 BTU | Ductless commercial air conditioner |
| 3/8 + 3/4 in. | 4.5–6.0 Ton / 4.5P–6P | 54,000–72,000 BTU | Large split air conditioner installation |
| 3/8 + 7/8 in. | 6.0–8.0 Ton / 6P–8P | 72,000–96,000 BTU | High-capacity ductless mini split system |
These capacity values are general product-family references only. Final refrigerant-line sizing must follow the HVAC equipment manufacturer's exact requirements.
Important Checks Before Installation
Confirm the Required Pipe Sizes
Verify that the selected HVAC equipment specifically requires a 1/4 in. liquid line and 1/2 in. suction line.
Verify the Permitted Piping Length
Confirm that the equipment manufacturer permits the proposed 25 ft refrigerant piping route.
Check Maximum Elevation Difference
If the indoor and outdoor units are installed at different elevations, verify the manufacturer's maximum permitted vertical separation.
Check Refrigerant Charge Requirements
Confirm whether the 25 ft installation falls within the equipment's factory refrigerant-charge allowance and follow the manufacturer's charging instructions.
Verify Communication Cable Specification
Confirm that the supplied communication cable matches the electrical and communication requirements of the selected mini split system.
Plan the Condensate Drain Route
Route the drain hose with suitable slope and follow the indoor-unit manufacturer's condensate drainage requirements.
Installation Guidelines
Inspect the Pre-Flared Connections
Inspect each copper flare before connection and tighten flare nuts according to the HVAC equipment manufacturer's specified torque.
Avoid Sharp Bends
Use appropriate HVAC tube-bending methods and suitable bend radii to reduce the risk of tube deformation and refrigerant-flow restriction.
Protect the Insulation
Avoid crushing, cutting or leaving unnecessary gaps in the insulation around bends, supports and wall penetrations.
Use the Wall Sleeve at Penetrations
Use the wall sleeve and protective cover where the piping passes through the building structure to help protect the tubing and insulation.
Pressure Test and Evacuate Before Startup
Refrigerant piping should be leak-tested, evacuated, charged and commissioned according to the HVAC equipment manufacturer's instructions and applicable local requirements.
OEM and Custom Installation Kit Options
White PE or Black Rubber insulation options
Custom insulation color
Logo printing on insulation
Custom line-set lengths
Custom copper pipe sizes
Wall-thickness options
Retail and wholesale packaging
OEM and ODM configurations
Complete Copper Pipe Installation Kit

DABUND HVAC Installation Kit Factory
DABUND manufactures insulated copper pipe, mini split line sets, aluminum pipe and related HVAC installation components for distributors, contractors and project buyers.

Insulation Test Documentation
The source certificate section states that applicable Polypropylene or Black Rubber insulation configurations can meet ASTM E84, UL94, ASTM D1056 and ASTM G21 requirements according to product specification.
White PE is the primary insulation configuration shown in the family table and product images on this page. Buyers requiring compliance documentation for White PE should therefore confirm the exact insulation material, thickness and matching test report for the ordered kit.

International HVAC Exhibitions
DABUND participates in HVAC exhibitions where professional buyers can evaluate mini split line sets, installation kits and related HVAC components.

Frequently Asked Questions
What is included in the 25 ft 1/4 x 1/2 installation kit?
The source kit includes a 25 ft 1/4 x 1/2 insulated copper line set, communication cable, approximately 3 m drain hose, wall sleeve, protective cover and pre-flared copper ends with nuts.
How long is the copper line set?
This SKU is 25 ft long, approximately 7.62 m.
What HVAC system size can use a 1/4 x 1/2 line set?
The DABUND product-family table lists 1/4 x 1/2 as a general reference for some 1.5–2.0 ton or 12,000–18,000 BTU systems. Final tubing size must follow the HVAC equipment manufacturer's exact requirements.
Are the copper pipe ends pre-flared?
Yes. The source page states that both ends are pre-flared and supplied with copper nuts.
What copper material is used?
The source page specifies 99.9% pure copper and references ASTM B280 and C12200.
What insulation options are available?
White PE and Black Rubber insulation options are listed. White PE is the primary insulation configuration shown in the product imagery and family table.
What insulation thicknesses are available?
The wider White PE installation-kit family table lists 8 mm, 9 mm, 10 mm, 13 mm, 19 mm and 25.4 mm insulation thickness options.
Does the kit include communication cable?
Yes. Communication cable is listed in the source package. Confirm the conductor specification and compatibility with the selected HVAC equipment.
Does the kit include a drain hose?
Yes. The source page lists an approximately 3 m condensate drain hose.
Does the kit include a wall sleeve and protective cover?
Yes. A wall sleeve and protective cover are included according to the source kit description.
Is 25 ft suitable for every mini split installation?
No. Confirm the HVAC equipment manufacturer's minimum and maximum permitted piping lengths, elevation limits and refrigerant-charge requirements before installation.
Can this installation kit be used outdoors?
UV-resistant insulation configurations are referenced on the source page. Final outdoor suitability should be confirmed for the exact insulation material and environmental conditions.
Can this kit be used with modern HVAC refrigerants?
The source describes the copper tubing as designed for HVAC refrigerant-line applications. Final refrigerant compatibility must be confirmed against the equipment manufacturer's required copper tube size, wall thickness, refrigerant and operating-pressure requirements.
Can DABUND customize the HVAC installation kit?
Yes. The source page lists custom insulation color, logo printing, pipe length, pipe size, wall thickness and packaging options for OEM and ODM orders.
Who typically buys this installation kit?
The product is intended for HVAC contractors, mini split brands, importers, distributors, wholesalers, project suppliers and professional installers.
Is professional HVAC installation recommended?
Yes. Refrigerant piping, electrical wiring, condensate drainage, flare connections, leak testing, evacuation, charging and system commissioning should follow the HVAC equipment manufacturer's instructions and applicable local requirements.