-
DBJ-003
-
DABUND
-
Copper
-
1M - 10M
Material
Color
Keywords
Application
10 ft 1/4 in. x 3/8 in. Mini Split AC Installation Kit
DABUND 10 ft 1/4 in. x 3/8 in. Mini Split AC Installation Kit provides the essential piping and installation accessories required for compatible ductless mini split air conditioners and heat-pump systems.
The kit includes a 10 ft pre-insulated copper refrigerant line set with a 1/4 in. liquid line and 3/8 in. suction line, together with control cable, a 3 m drain hose, wall pipe, wall cover and related installation accessories.
Both ends of the copper tubing are factory-flared and supplied with nuts, helping reduce field preparation during compatible mini split installation.
Quick Answer: This 10 ft mini split installation kit combines a 1/4 x 3/8 pre-insulated copper line set with control cable, condensate drain hose and wall installation accessories for compatible ductless AC systems.
10 ft Mini Split AC Installation Kit Video
What Is Included in the AC Installation Kit?
| Component | Specification |
|---|---|
| Copper Refrigerant Line Set | 1/4 in. + 3/8 in., 10 ft |
| Liquid Line | 1/4 in. / approximately 6.35 mm |
| Suction Line | 3/8 in. / approximately 9.52 mm |
| Line Set Length | 10 ft / approximately 3.05 m |
| Insulation | White PE configuration shown; other insulation options available |
| Copper Connections | Factory-Flared Ends with Nuts |
| Control Cable | Included |
| Drain Hose | 3 m |
| Wall Pipe and Cover | Included |
| Application | Compatible Mini Split and Ductless HVAC Installation |
1/4 in. Liquid Line and 3/8 in. Suction Line
The refrigerant line set combines a 1/4 in. liquid line with a 3/8 in. suction return line.
Both tube sizes should match the refrigerant piping dimensions specified by the mini split or heat-pump manufacturer. Do not select the installation kit based only on nominal system capacity.
Factory-Flared Copper Tube Ends with Nuts
Both ends of the copper tubing are supplied with factory-prepared flare connections and nuts.
Pre-flared connections can reduce field preparation work during compatible mini split installation. Final connection dimensions, flare condition and tightening requirements should always be checked against the HVAC equipment manufacturer's installation instructions.
Pre-Insulated Copper Refrigerant Tubing
The kit includes factory-insulated copper tubing to help reduce unwanted thermal exchange and condensation along the refrigerant piping.
The featured product configuration uses White PE insulation. The source product information also lists Black Rubber as an available insulation option for suitable orders.
White PE insulation thickness options listed by DABUND include 8 mm, 9 mm, 10 mm, 13 mm, 19 mm and 25.4 mm. Black Rubber insulation is also available in selected thicknesses.
Copper Pipe and Insulation Video
99.9% Pure Copper
White PE Insulated Pipe
Copper Nut
White PE Pipe Insulation Structure
The featured White PE insulation uses a multi-layer structure designed to provide thermal protection, moisture resistance and mechanical protection around the copper refrigerant tubing.
The source product information describes an embossed PE outer film, an IXPE foam middle layer and a closed-cell inner insulation structure.
The listed inner-layer temperature range is approximately -40°C to 120°C.
Insulation Production and Structure
Insulation Pipe Production
Insulation Pipe Warehouse
Inner Layer Insulated Pipe
Copper Tubing and Insulation Standards
The source product information references ASTM B280 and C12200 DHP for the copper tubing.
The insulation information references ASTM C1427-07, UL94, UL723 and ASTM E84, together with UV-resistant performance. Buyers requiring project-specific compliance should confirm the exact insulation material and corresponding test documentation for the ordered configuration.
Complete 10 ft Mini Split Installation Kit
Unlike a refrigerant line-set-only product, this AC installation kit includes additional components required for compatible mini split installation.
The kit combines refrigerant piping, electrical communication cable, condensate drainage components and wall penetration accessories in one package for distributors, installers and project buyers.
Applications
Compatible mini split air conditioners
Ductless heat-pump systems
Residential split-system installations
Light commercial mini split projects
Replacement installation projects requiring a 1/4 x 3/8 refrigerant line set
Refrigerant Compatibility
The source product information lists R410A and R32 among the refrigerants used with compatible mini split and HVAC systems.
Final refrigerant compatibility, required tubing dimensions, allowable pressure and connection requirements must be verified against the specific HVAC equipment manufacturer's technical documentation.
Available AC Installation Kit Sizes
| Line Set Size | Available Lengths | White PE Insulation | Listed Flame-Resistance Options |
|---|---|---|---|
| 1/4 + 3/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/4 + 1/2 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/4 + 5/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 5/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 3/4 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 1/2 + 3/4 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
| 3/8 + 7/8 in. | 3 m / 4 m / 5 m / 7 m / 10 m | 8 / 9 / 10 / 13 / 19 / 25.4 mm | M1 / B1 |
General Line Set Size and Capacity Reference
The following capacity ranges are general references from the wider DABUND product family. Final line-set sizing must follow the HVAC equipment manufacturer's exact refrigerant piping requirements.
| Line Set Size | General Ton Reference | General BTU Reference |
|---|---|---|
| 1/4 + 3/8 in. | 0.75–1.0 Ton | 9,000–12,000 BTU |
| 1/4 + 1/2 in. | 1.5–2.0 Ton | 12,000–18,000 BTU |
| 1/4 + 5/8 in. | 2.0–2.5 Ton | 24,000–30,000 BTU |
| 3/8 + 5/8 in. | 3.0–4.0 Ton | 36,000–48,000 BTU |
| 3/8 + 3/4 in. | 4.5–6.0 Ton | 54,000–72,000 BTU |
| 3/8 + 7/8 in. | 6.0–8.0 Ton | 72,000–96,000 BTU |
For the 1/4 x 3/8 configuration, the DABUND product family lists 0.75–1.0 ton and 9,000–12,000 BTU as general references. Actual compatibility must be confirmed from the refrigerant line dimensions specified by the HVAC equipment manufacturer.
Installation Guidelines
Confirm the Required Line Set Size
Verify that the HVAC equipment specifically requires a 1/4 in. liquid line and 3/8 in. suction line before installation.
Confirm the 10 ft Length
Measure the complete route between the indoor and outdoor units before ordering to confirm that the 10 ft line set provides sufficient installation length.
Protect the Factory Flare Connections
Inspect the flare surfaces and nuts before connection and follow the HVAC equipment manufacturer's specified tightening method and torque requirements.
Avoid Sharp Bends and Kinks
Route the copper tubing using appropriate bend radii to reduce the risk of kinking or restricting refrigerant flow.
Protect the Insulation at Wall Penetrations
Use the appropriate wall pipe, sleeve or protective components where the line set passes through the building structure to reduce abrasion and insulation damage.
Route the Drain Hose Correctly
Where gravity drainage is used, route the condensate hose with an appropriate downward slope and avoid kinks that could restrict water flow.
Follow the HVAC Equipment Manufacturer's Instructions
Refrigerant piping, electrical connections, evacuation, charging, condensate drainage and system commissioning should follow the equipment manufacturer's instructions and applicable installation requirements.
Why Choose the DABUND 10 ft AC Installation Kit?
Multiple Installation Components in One Kit
The package combines refrigerant tubing, communication cable, condensate drain hose and wall accessories to simplify sourcing for compatible mini split projects.
Factory-Flared Refrigerant Tubing
Copper tube ends are supplied with flare connections and nuts to reduce field preparation for compatible systems.
Factory-Applied Insulation
Pre-insulated refrigerant tubing reduces additional insulation work and provides consistent thermal protection around the copper lines.
DABUND AC Installation Kit Factory
DABUND has produced HVAC parts since 2008 and manufactures insulated copper pipe, mini split line sets, AC installation kits, aluminum pipe and related HVAC products for distributors and project customers.
Insulation Test Documentation
The source product information references ASTM E84, UL94, ASTM D1056 and ASTM G21 for applicable insulation configurations, while the copper tubing is listed with ASTM B280 and C12200 references.
Because the featured kit on this page shows White PE insulation while the certificate section also references Polypropylene or Black Rubber, buyers requiring a specific compliance document should confirm the insulation material and corresponding test report for the ordered configuration.
International HVAC Exhibitions
DABUND participates in international HVAC exhibitions where distributors and professional buyers can review mini split line sets, installation kits and related HVAC products.
Frequently Asked Questions
What is included in the 10 ft AC installation kit?
The source product information lists a 10 ft 1/4 x 3/8 pre-insulated copper refrigerant line set, control cable, 3 m drain hose, wall pipe, wall cover and related installation accessories.
What does 1/4 in. x 3/8 in. mean?
It refers to the outside diameters of the two refrigerant tubes: a 1/4 in. liquid line and a 3/8 in. suction return line.
How long is the copper line set?
The refrigerant line set is 10 ft long, approximately 3.05 m.
Are the copper tubing ends already flared?
Yes. The source product information states that both ends are factory-flared and supplied with nuts.
Is the refrigerant tubing pre-insulated?
Yes. The copper refrigerant tubing is supplied with factory-applied insulation.
What insulation options are available?
The source product information lists White PE and Black Rubber insulation options. The featured configuration on this page uses White PE insulation.
What White PE insulation thicknesses are available?
Listed White PE thicknesses include 8 mm, 9 mm, 10 mm, 13 mm, 19 mm and 25.4 mm.
What other installation kit lengths are available?
The wider AC installation kit family lists 3 m, 4 m, 5 m, 7 m and 10 m production lengths.
What size mini split can use a 1/4 x 3/8 line set?
The DABUND product family lists 1/4 x 3/8 as a general reference for some 0.75–1.0 ton or 9,000–12,000 BTU mini split systems. Final line-set sizing must follow the equipment manufacturer's exact refrigerant piping requirements.
Can every mini split use this 10 ft installation kit?
No. Confirm the refrigerant tube sizes, connection dimensions, cable requirements, drain connection and required line length for the specific equipment before installation.
Is this installation kit compatible with R410A and R32?
R410A and R32 are listed among the compatible refrigerants. Final suitability should be verified against the specific HVAC equipment manufacturer's technical specifications.
Can the insulated copper line be installed outdoors?
The source product information describes the insulation as UV-resistant. Final outdoor suitability should be confirmed for the selected insulation configuration and installation conditions.
What standards are referenced for the copper tubing?
ASTM B280 and C12200 DHP are referenced for the copper tubing in the source product information.
Is DABUND a manufacturer?
Yes. The source product information identifies DABUND as a manufacturer of HVAC parts and mini split installation products.
Can DABUND provide free samples?
Yes. The listed sample policy provides up to three free samples for qualified requests, with the buyer paying the express freight. View Sample Information
What payment terms are available?
Listed payment options include T/T, L/C at sight and credit card.
What delivery terms are available?
Listed delivery terms include EXW, FOB, CFR and CIF.
Does DABUND support OEM and ODM?
Yes. OEM and ODM services, including logo customization, are available for suitable orders.
What is the typical delivery time?
The listed typical delivery time is approximately 15–20 days, depending on order quantity and production requirements.
